Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
The article author is making a few good pointers about Tools You Need to Install a New Bathtub in general in the content in the next paragraphs.
Mounting a tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult task. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open a wall to eliminate the old tub and also position the new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job as well as are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have already acquired a new bathtub and don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the restricted gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the spirit level checks out level.
To set up taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making certain that the washers remain in place between the tap as well as the sink. Safeguard the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous kind needs to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, causing issues with dampness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that review on How to Install a Bathtub when doing a search on the internet. For those who liked our article if you please be sure to share it. We treasure reading our article about How to Install a Bathtub Yourself.
Book Today!
Report this page